Schedule Now!

 

 

Presented here below you will find additional really good advice regarding Tools You Need to Install a New Bathtub .

Setting up a bath tub isn't specifically rocket science, however it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily available, the project can relocate immediately; if you have to open up a wall surface to eliminate the old tub and also place the new bath tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have actually certified yourself for the task and fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you set up a brand-new bathtub in your shower room if you have already acquired a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Getting ready for the Installment

First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its final setting.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

 

 

Installing the Bathtub

Making use of both wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the proper supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leakages and also tighten them if essential. Load the tub and also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the tub should wait until the bath tub has actually been utilized at least once as this will settle it into its last placement.

 

 

Suitable New Touches

If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap as well as the sink. Secure the faucet in position with the supplier supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am just very curious about Tools You Need to Install a New Bathtub and I am assuming you liked the new blog post. If you liked our post please don't forget to pass it around. We love reading our article about Installing A Bathtub.

Start Now